Probably, until the end of the XIX century rotary knitting by means of spokes with two pointed ends was the most widespread type of knitting. Now many knitters rediscover for themselves advantages of this equipment.
As when knitting around the upper side of work always is before your eyes, it is much easier to carry out practically any pattern of knitting, including braid, and especially patterns of color knitting with broaches. As for chulochny knitting, each row matches front loops. Elastic bands and pearl knitting are carried out in the same way, but with set of even number of loops. Carrying out platochny knitting, you should alternate ranks of front and back loops.
It is very simple to knit according to schemes: you read each number of the scheme from right to left, lowering thus selvage loops. Plaits can be bound in any row, the crossed loops can be carried out in each row and color samples match much easier. All types of seamless products the spendthrift to be knitted on I twist — caps, socks, gloves and sweaters. Flat and rotary knitting mogutbyt are combined for creation product in which the number of seams has to be minimized.
KNITTING BY CHULOCHNY SPOKES
Spokes are on sale in sets from four or five spokes. Four — this minimum number of spokes which is required for forming of circle — on three spokes are loops, and the fourth spoke carries out knitting. You can use any quantity of spokes with two ends what will be required for larger detail.
Gather loops in the usual way, divide them into number of spokes minus one. Watch that loops on spokes were not crossed, reduce together the first and last spokes and start knitting free spoke. In the beginning it seems that to knit several spokes not so quickly, however, as soon as you will accustom with the most convenient arrangement of tips of spokes — one tip over another, business will go quicker. Watch that the thread was strong tense every time when you provyazyvat the first loop from the following spoke, differently the short flight of stairs can be formed of wider loops.
Set of loops at rotary knitting on chulochny spokes.
For this purpose the set from 5 chulochny spokes and for big products circular spokes will be required.
KNITTING BY CIRCULAR SPOKES
Are ideal for rotary knitting of larger products. Gather required number of loops, then bring the end of one spoke to the end another and begin knitting. Be convinced that the loops which are on spoke are not overwound. Again check the provision of loops after performance of the first row. Pass to circular spokes of the smaller size or use set from spokes with two sharp ends if you carry out ubavka and loop do not slide freely round the spokes which were originally used in work.
Ways set of loops when knitting from the center:
By means of hook. Several times reel up working thread on finger of the left hand, forming two rings. Further remove these rings, holding them. Tie with hook ring, having gathered necessary quantity of loops on spokes to start knitting. For this purpose pass hook through the received rings, take thread, extend it. On hook the loop through which stretch thread again turns out and tighten; so, the second loop under rings was formed and it put on spoke; so form necessary quantity of loops gathering them on spokes.
If the ring from thread has appeared big, carefully pull for the end pulling together it. Having gathered necessary quantity of loops on spokes begin knitting provyazav the first row with front loops, entering spoke from face inside out. The first row knit accurately and attentively as the loops which are carried out by hook are a little elastic and can tear. After initial front row distribute loops on spokes and start knitting the chosen pattern.
By means of spokes. This way reminds the set executed by hook, but the knitting spoke is used here.
Spoke in the right hand. Working thread obkrutit forefinger of the left hand, spoke pick up the thread going from ball, extend the first loop. Make nakid, extend the following loop, etc. Loops and nakida to repeat, the necessary quantity of loops will not be reached yet. Gather 8 or 12 loops and distribute them on 4 spokes. Provyazhite some ranks, pull for the free end of thread and pull together loops.
Such set of loops is used at lacy knitting, for example, at the beginning of knitting of napkins, cloths, scarfs. It is very convenient when loops of one rapport are not located partially on one, and partially on other spoke. It is best of all if on spoke there are finished rapports.
Knitting of geometrical figures from the center:
No comments:
Post a Comment